Yanmar 3YM30 / 3YM20 / 2YM15 maintenance schedule
The Yanmar 3YM30 / 3YM20 / 2YM15 service schedule as Yanmar Marine publishes it, set out as a checklist for the crew: the work due at 50, 100, 150, 250, and 1000 engine hours, the parts to have aboard, and the fluids the manual specifies.
Put the Yanmar 3YM30 / 3YM20 / 2YM15 schedule on your boat
HelmOps turns the Yanmar 3YM30 / 3YM20 / 2YM15 service intervals into reminders, parts lists and a service record that works offline at sea. 30 days free, no card.
Track this engine freeImportant service notice
This page is a general maintenance planning guide for yacht operations. It is not an OEM service manual and does not override the official Yanmar Marine manual, warranty terms, class requirements, flag-state obligations, oil analysis recommendations, or dealer instructions for your exact engine serial number and installation.
The intervals, tasks and fluid specifications below are taken from Yanmar YM Series Operation Manual (2YM15, 3YM20, 3YM30AE), 0AYMM-M0002E (2025). Schedule: p. 53-56. Open the Yanmar Marine document
Where this engine is used
Yanmar presents the schedule for pleasure use as a general guideline that varies with load and fuel. On the YM series the engine oil is changed every 150 hours or 1 year, while the oil filter stays on the 250-hour service. Coolant is replaced every year, or every 2 years with Yanmar Long Life Coolant. Items marked for a Yanmar dealer include fuel injection timing and the injector spray pattern at 1000 hours.
- Auxiliary propulsion for small sailing yachts
- Motor-sailers and small displacement cruisers
In yacht service, maintenance timing is shaped by more than the hour meter. Long idle periods, high-load passages, warm engine rooms, saltwater exposure, seasonal lay-up, charter schedules, fuel quality, and access constraints all affect when work should be planned. A good schedule therefore combines engine hours, calendar time, oil analysis, visual inspection, alarm history, and the captain's operating notes.
Daily checks
The manual lists these checks for each day the engine is used.
- Visually inspect engine exterior
- Check fuel level and refill if necessary
- Check engine oil level
- Check marine gear oil level
- Check seawater outlet during operation
- Check coolant level
- Check exhaust gas condition during operation
- Check for fuel, oil and coolant leaks after starting
- Check alarm and indicators
First service after 50 hours
The manual calls for this one-off service on a new engine after its first 50 hours of running. The regular intervals below apply from then on.
- Drain water and sediment from fuel tank
- Change engine oil and replace engine oil filter element
- Change marine gear oil
- Check and adjust alternator V-ribbed belt tension
- Adjust intake/exhaust valve clearance
- Check and adjust remote control cables
- Adjust propeller shaft alignment
Service interval checklist
Every 50 engine hours or 1 month, whichever comes first
Treat the 50-hour milestone as a planning checkpoint. Confirm parts availability, assign the work to a qualified marine engineer, and record findings with photos, meter readings, invoice references, and follow-up tasks.
- Drain the fuel filter / water separator
- Check battery electrolyte level (serviceable batteries only)
Every 100 engine hours or 6 months, whichever comes first
Treat the 100-hour milestone as a planning checkpoint. Confirm parts availability, assign the work to a qualified marine engineer, and record findings with photos, meter readings, invoice references, and follow-up tasks.
- Change sail drive gear oil (sail drive installations only)
Parts to prepare
Sail drive gear oil
Every 150 engine hours or 12 months, whichever comes first
Treat the 150-hour milestone as a planning checkpoint. Confirm parts availability, assign the work to a qualified marine engineer, and record findings with photos, meter readings, invoice references, and follow-up tasks.
- Change engine oil
Parts to prepare
Engine oil
Every 250 engine hours or 12 months, whichever comes first
Treat the 250-hour milestone as a planning checkpoint. Confirm parts availability, assign the work to a qualified marine engineer, and record findings with photos, meter readings, invoice references, and follow-up tasks.
- Drain water and sediment from fuel tank
- Replace fuel filter element
- Replace engine oil filter element
- Change marine gear oil
- Check seawater pump impeller
- Clean intake silencer (air cleaner) element
- Clean or replace exhaust / water mixing elbow
- Clean breather pipe, check alternator belt tension and wiring connectors
Parts to prepare
Fuel filter element, Engine oil filter element, Marine gear oil, Seawater pump impeller, Exhaust / water mixing elbow
Every 1000 engine hours or 48 months, whichever comes first
Treat the 1000-hour milestone as a planning checkpoint. Confirm parts availability, assign the work to a qualified marine engineer, and record findings with photos, meter readings, invoice references, and follow-up tasks.
- Replace seawater pump impeller
- Replace alternator V-ribbed belt
- Check fuel injection timing and injector spray pattern (dealer)
- Clean and check seawater passages (dealer)
- Check diaphragm assembly (dealer)
- Adjust intake/exhaust valve clearance
- Tighten all major nuts and bolts
- Check remote control cables and adjust propeller shaft alignment
Parts to prepare
Seawater pump impeller, Alternator V-ribbed belt
Track these intervals from your hour meters
In HelmOps, the crew enter hour meter readings and each service turns due soon and then overdue as the engine runs, with alerts to the owner and captain. See how our yacht planned maintenance software tracks engine hours
Oil and coolant specifications
Specifications from Yanmar YM Series Operation Manual (2YM15, 3YM20, 3YM30AE), 0AYMM-M0002E (2025). Check the viscosity chart in your engine's manual against the temperatures you expect to operate in.
- Engine oil
- API CD, CF, CF-4, CI or CI-4; SAE 10W-30 or 15W-40 (usable all year); never API CG-4 or CH-4
- Coolant
- Long Life Coolant (Texaco LLC product code 7997/7998 or Havoline Extended Life 7994), 30% to 60% concentration, mixed with soft water
- Gearbox oil
- KM2P-1 marine gear: API CD or higher, SAE #20 or #30. SD25 sail drive: API GL4.5, SAE 90 or 80W-90
Engine running-hours log
Log meter readings for each engine, see the hours between entries and track hour-based services. A service turns amber with 50 hours or less to go and red when it is due.
Crew planning notes
The safest way to manage Yanmar 3YM30 / 3YM20 / 2YM15 maintenance is to keep the next service visible in the vessel's operating rhythm. The chief engineer or captain should review the hour meter at each handover, compare it with the planned route, and reserve workshop time before a busy charter period begins. For twin-engine yachts, keep port and starboard records separate even when both engines are serviced on the same day.
Parts planning matters as much as the checklist. Filters, belts, coolant, zinc anodes, impellers, approved oils, gaskets, and specialist tooling may not be available at short notice in smaller cruising grounds. For larger Yanmar Marine installations, diagnostic access and authorised technician availability can become the real constraint. Captains should therefore turn each interval into a task list with owner approval status, purchasing notes, supplier details, and target dates.
Service evidence should be complete enough for a future buyer, surveyor, manager, insurer, or flag-state inspector to understand what happened. A useful record includes the date, engine hours, engineer name, parts used, fluid quantities, photographs, oil analysis files where available, defects found, corrective actions, and the next due hour. When maintenance is tracked only in chat messages or paper invoices, it becomes difficult to prove that the vessel followed a disciplined programme.
Cooling-system work deserves special attention. Raw water strainers, impellers, heat exchangers, thermostats, anodes, hose clamps, and exhaust components all live in a harsh saltwater environment. A small restriction or worn impeller can become an overheating event under load. If the yacht is used seasonally, inspect the raw water side before the first serious passage rather than waiting for the next hour milestone.
Fuel quality also drives reliability. Water contamination, biological growth, blocked pre-filters, and air leaks can stop an otherwise healthy diesel engine. Each fuel filter service in the schedule is a good moment to compare filter condition with fuel history, tank cleaning records, and recent bunker locations. Any repeated filter restriction should be treated as an operational issue, not just a parts replacement.
Frequently asked questions
What are the service intervals for a Yanmar 3YM30 / 3YM20 / 2YM15?
The Yanmar Marine manual cited on this page sets Yanmar 3YM30 / 3YM20 / 2YM15 service work at 50, 100, 150, 250, and 1000 engine hours. The tasks for each interval are listed above. Power ratings, model years and operating conditions can differ, so confirm the schedule against the manual for your engine's serial number.
What oil specification should I use for a Yanmar 3YM30 / 3YM20 / 2YM15?
The Yanmar Marine manual cited on this page specifies API CD, CF, CF-4, CI or CI-4; SAE 10W-30 or 15W-40 (usable all year); never API CG-4 or CH-4. Choose the viscosity for the temperatures you operate in, and if your manual specifies something different, confirm the grade with an authorised dealer or service provider.
When should the raw water impeller be replaced on a Yanmar 3YM30 / 3YM20 / 2YM15?
Follow the seawater pump impeller interval in the Yanmar Marine schedule above. Replace it sooner if you find cracked or missing vanes, see overheating or weak raw water flow, or do not know when it was last changed.
Track Yanmar 3YM30 / 3YM20 / 2YM15 maintenance in HelmOps
HelmOps helps captains and yacht managers turn engine-hour schedules into recurring tasks, service evidence, purchasing notes, and owner-ready maintenance records across the vessel.